3D Printed Electronics Enclosures, Knobs, and Housings

Knobs, battery doors, bezels, housing halves, and clips for audio gear, instruments, tools, and vintage electronics, plus custom enclosures for new projects.

What we do

The electronics inside still work. The plastic around them did not survive. A knob on a vintage receiver or synth, the battery door on a camera or a test meter, the bezel on a radio, a cracked housing half on a tool, the clip that held a cover closed. Manufacturers do not stock these, and the aftermarket covers only the most popular models.

Mail us the broken part, or the intact matching one, and we scan it, rebuild it, and print it in a material that matches the job. ASA or PETG for housings, nylon for clips and snap fits, polycarbonate where heat or impact matters, flexible TPU for feet and bumpers. If you are building something new, send a sketch or a board outline and we model an enclosure from scratch with standoffs, cutouts, and a lid that fits.

Housings, knobs, and mechanical parts only. We do not repair the electronics themselves.

Examples of typical work

Printed black battery door snapped onto the back of a handheld meter beside the cracked original door
Battery door with its tab rebuilt
Surviving tool housing half beside its printed copy with the internals in a parts tray behind
Housing half reproduced from the surviving side
Printed green enclosure opened to show the circuit board it was modeled around
Custom enclosure for a new board

Example images of typical work, to help you picture your part. Have something like this? Send a photo for a quote.

Parts we make most

Knobs and sliders

Potentiometer and encoder knobs with the right shaft fit for audio gear, synths, test equipment, and appliances.

Battery doors and covers

Battery compartment doors, port covers, and access panels with working latches.

Bezels and faceplates

Display bezels, radio faceplates, button surrounds, and trim rings.

Housing halves and shells

Cracked tool, remote, and handheld device shells reproduced from the surviving half.

Clips, feet, and brackets

Snap clips, cable clips, rubber feet, and mounting brackets.

Custom enclosures

New housings for boards, sensors, and displays modeled from a sketch or board file, with standoffs and cutouts.

Pinball and arcade parts

Plastic ramps, guides, post caps, coin door and cabinet parts for restorations, reproduced from the original or its broken pieces.

Material by job

We choose the material from what the part has to survive, not from what it was originally made of.

Where the part livesMaterialWhy
Housings and bezelsASA or PETGDimensionally stable, good surface finish, available in many colors.
Clips and snap fitsNylonFlexibility depends on the grade and geometry.
Near heat or impactPolycarbonateTool housings and parts near power supplies.
Feet and bumpersTPUFlexible and grippy.

How it works

One. Send one photo and two measurements with the quote form, and we send you a quote. Two. Mail the part to the address we send you, every fragment included, or in our Georgia pickup area ask us to pick it up. Three. We scan it, rebuild the geometry, and confirm the price and ship date in writing. Four. Approve, and we print, finish, and ship the part back with your original.

No CAD file, no appointment, no minimum. One part is fine, and a batch of spares is cheaper per piece once the part is modeled.

Common questions

Can you match the shaft of my knob?
Yes. Send the knob, or tell us the shaft type (D shaft, splined, round with set screw) and diameter. We scan the original fit or model to the standard.
Can you reproduce a knob set for a vintage receiver?
Yes. Send one intact knob and we scan it and print the set. Finishes like brushed metal cannot be printed, but many customers paint or cap the printed knobs.
Can you design an enclosure for my circuit board?
Yes. Send the board dimensions or a board file, the connector positions, and how it mounts, and we model an enclosure with standoffs, cutouts, and a lid. Revisions after the first print are normal.
Can you print a translucent part for an LED?
Yes, in clear or tinted polycarbonate or PETG.
Do you repair the electronics?
No. We make the mechanical and housing parts. Your electronics tech does the rest.
How many can you make?
One or a batch. Once modeled, additional copies are inexpensive.

Ready to start?

One photo, two measurements, and we send you a quote. You get the price and the turnaround in writing before any work begins.

Get a Free Quote

← All replacement parts