3D Printed Replacement Appliance Parts

Knobs, clips, handles, hinges, and brackets for stoves, fridges, washers, dryers, dishwashers, and mixers the manufacturer stopped supporting.

What we do

A twenty year old range works perfectly except for the one knob that cracked, and the manufacturer wants you to buy a new range. A dishwasher rack roller, a fridge shelf clip, a dryer door latch, a stand mixer lever. These are the parts that take an appliance out of service and the parts nobody stocks.

Mail us the broken piece, even in fragments. We 3D scan it, rebuild the geometry, and print a replacement in a material chosen for where it lives. Heat exposure needs a grade-specific review. We do not approve printed parts for dishwasher interiors or safety controls. Flexible TPU can be considered for noncritical feet and bumpers. You get a price and a ship date before anything prints.

If the manufacturer still sells the part, buy theirs. This service exists for the parts you cannot buy at any price.

Examples of typical work

Cracked white range knob beside a new printed match on a kitchen range
Cracked knob and its printed match
Printed white shelf support clip holding a glass shelf inside a refrigerator door
Fridge door shelf clip, printed in white
Printed gray dryer door catch fitted to a white dryer with the worn original on top
Dryer door catch rebuilt from the worn one
Printed black release lever on the side of a red stand mixer head on a kitchen counter
Mixer release lever, printed to fit
Printed gray door hook on an open microwave door with the broken original below
Microwave door hook, the part nobody stocks
Printed frosted handle trim on a crisper drawer pulled out of a refrigerator
Crisper drawer handle printed in clear

Example images of typical work, to help you picture your part. Have something like this? Send a photo for a quote.

Parts we make most

Knobs and dials

Stove, oven, washer, and dryer knobs with the correct D shaft or spline, in a material chosen after a heat review and matched to the original look.

Clips, rollers, and rack parts

Fridge shelf clips, drawer glides, crisper drawer rails.

Handles, latches, and hinges

Door handles, lid latches, microwave door hooks, and hinge covers that snap or shear.

Mixer and small appliance parts

Stand mixer levers, blender base couplers, food processor lid tabs, coffee maker brackets.

Gaskets, feet, and bumpers

Flexible TPU replacements for rubber parts that were never sold separately.

Vent, duct, and bracket parts

Range hood baffles and brackets, dryer vent adapters, mounting brackets for wall units.

Material by job

We choose the material from what the part has to survive, not from what it was originally made of.

Where the part livesMaterialWhy
Knobs near heatPolycarbonate or ASACandidate grades only. Confirm the actual temperature and safety function before choosing a material.
Wet or detergent exposureReview requiredNo approved printed dishwasher parts. Give us the cleaner, temperature and contact time.
Snap fits and clipsNylonA candidate for clips after checking deflection, grade and moisture.
Gaskets and feetTPUFlexible, grippy, and durable.

How it works

One. Send one photo and two measurements with the quote form, and we send you a quote. Two. Mail the part to the address we send you, every fragment included, or in our Georgia pickup area ask us to pick it up. Three. We scan it, rebuild the geometry, and confirm the price and ship date in writing. Four. Approve, and we print, finish, and ship the part back with your original.

No CAD file, no appointment, no minimum. One part is fine, and a batch of spares is cheaper per piece once the part is modeled.

Common questions

Can you make a stove knob that matches the others?
We match the shaft fit, the geometry, and the general look. Color is matched as closely as the material allows. If you have one intact knob, send it along with the broken one so we can scan the good example.
Is 3D printed plastic safe near a hot oven?
Suitability depends on the actual exposure, load and material grade. We do not approve a part from a heat-deflection value alone, or print parts for the oven cavity, direct flame or safety controls.
Are printed parts food safe?
We do not recommend printed parts for direct, repeated food contact such as blender blades or cutting surfaces. Exterior parts still need a review of cleaning, heat and accidental food contact.
What does an appliance part cost?
It is quoted per part. Simple knobs and clips are at the low end. Complex housings with many features are more. Scanning and modeling is usually the biggest part of the price, so a second identical part is much cheaper than the first.
What if I only have the broken pieces?
Send them all. A part that broke cleanly carries its full geometry between the pieces. If a section is missing we rebuild it from what survives and from the part it mates with.
How long does it take?
We quote the turnaround with the price before starting. The part has to reach us by mail, then scanning, modeling, printing, and return shipping follow.

Ready to start?

One photo, two measurements, and we send you a quote. You get the price and the turnaround in writing before any work begins.

Get a Free Quote

← All replacement parts